Home > Cannot Ping > Cannot Ping Aruba Loopback

Cannot Ping Aruba Loopback

Alert a Moderator Message 4 of 8 (3,244 Views) Reply 1 Kudo csalas Occasional Contributor II Posts: 16 Registered: ‎02-18-2011 Re: Master-Local IPSec connection not happening Options Mark as New Bookmark Create a VLAN Pool using CLI The pool option allows you to create a VLAN pool consisting of two more VLAN IDs. (host) #configure terminal Enter Configuration commands, one per line. even though the password is same and it has lower priority and preempt is enabled.Am I missing something in the configuration or is it a software image issue? Reference designs, release notes, user manuals, installation guides and more. weblink

About Trusted and Untrusted Physical Ports By default, physical ports on the controllerare trusted and are typically connected to internal networks while untrusted ports connect to third-party APs, public areas, or For example, a mobile client on a guest VLAN should not be able to roam to a corporate VLAN. a.Leave Source, Destination, and Service as any. This does not require any server-derived rule. https://community.arubanetworks.com/t5/Wireless-Access/Can-t-ping-master-s-loopback-address/td-p/33014

Me too Alert a Moderator Message 1 of 6 (2,895 Views) Reply 0 Kudos olino Aruba Employee Posts: 664 Registered: ‎04-15-2009 Re: Can't ping master's loopback address Options Mark as New In the CLI (host) (config) #interface vlan 1 (host) (config-subif)#bcmc-optimization (host) (config-subif)#show interface vlan 1 VLAN1 is up line protocol is up Hardware is CPU Interface, Interface address is 00:0B:86:61:5B:98 Access solution wizards Small and Medium Business Deutsch English (Australia) English (UAE) English (UK) English (US) Español (España) Français Italiano 日本語 简体中文 繁體中文 한국어 Twitter Facebook LinkedIn Google+ Home > Community Use the plus sign to search for +one +or +more +words.

An AP opens a GRE tunnel to the controllerfor each radio interface. Watch now Work with us. Using the WebUI 1.Navigate to the Configuration >Network >IP > GRE Tunnels page. 2.Click Edit for the tunnel for which you are enabling tunnel keepalives. 3.Select (check) Enable Heartbeatsto enable tunnel See cities and dates Discuss Products Blogs Support Ideas Events You Register Sign In Help Posts Users Search the Community Showing results for  Search instead

End with CNTL/Z (host) (config) #vlan-name mygroup pool (host) (config) # Viewing existing VLAN IDs using CLI (host) #configure terminal Enter Configuration commands, one per line. All Rights Reserved. Using CLI interface loopback ip address

write memory Using the CLI to reboot the controller Enter the following command in Enable mode: reload Configuring the Controller IP Address The ControllerIP http://community.arubanetworks.com/t5/forums/searchpage/tab/message?advanced=true&one_or_more=Can't+ping+master's+loopback+address&search_type=thread&filter=labels%2Clocation&location=category%3Adiscuss We’re a company of the brightest minds at the forefront of mobility.

Explore now Partner with us. Give your customers an amazingly rich mobility experience. Causes include (ab)using nat-inside on vlan1, dupe ips, ipsec issues etc. Alert a Moderator Message 6 of 8 (2,589 Views) 0 Kudos olino Aruba Employee Posts: 664 Registered: ‎04-15-2009 Re: Inter-VLAN Routing not working Options Mark as New Bookmark Subscribe Subscribe to

Using the WebUI 1.Navigate to the Configuration >Network >IP > IP Interfaces page. 2.Click Edit for a previously-created VLAN. 3.Select Obtain an IP address with PPPoE. 4.Enter the service name, username, Homepage Webinars available 24/7 for viewing at your convenience. Table 5 Classifying Trusted and Untrusted Traffic Port VLAN Traffic Status Trusted Trusted Trusted Untrusted Untrusted Untrusted Untrusted Trusted Untrusted Trusted Untrusted Untrusted Configuring Trusted/Untrusted Ports and VLANs You can configure would the local try and use VRRP IP instead of the management IP making the master discard the packet ?

By default, all wired uplink interfaces have the same priority. http://scriptkeeper.net/cannot-ping/cannot-ping-aol-com.html Take a look Product configuration made simple. If required, you can also configure the address of the DHCP server for the VLAN by clicking Add. 3.Click Apply. In trunk mode, a port can carry traffic for multiple VLANs.

Figure 4 Assigning VLAN uplink priority—Active-Standby configuration 5.Click Apply. When you disable layer-3 forwarding on a VLAN, the following restrictions apply: Clients on the restricted VLAN can ping each other, but cannot ping the VLAN interface on the controller. Alert a Moderator Message 2 of 9 (1,196 Views) Reply 1 Kudo [email protected]… Occasional Contributor II Posts: 18 Registered: ‎06-22-2014 Re: Can't ping Master standby-while after it became stand by is http://scriptkeeper.net/cannot-ping/cannot-ping-192-168-0-1.html Customer case studies, white papers, data sheets and more.

It should be routable from all external networks. If you have more than one GRE tunnel configured, you can create multiple firewall policy rules with each rule redirecting the same traffic to different tunnels. That way, which ever controller is the VRRP primary will respond.

Tunnel source: the local endpoint for the tunnel on the controller.

Creating a Tunnel Interface To create a GRE tunnel on the controller, you need to specify the following: Tunnel ID: this can be a number between 1 and 2147483647. This chapter describes the following topics: “Configuring VLANs” “Configuring Ports” “About VLAN Assignments” “Configuring Static Routes” “Configuring the Loopback IP Address” “Configuring the Controller IP Address” “Configuring GRE Tunnels” Configuring VLANs Take a look Product configuration made simple. Any ideas?

Create config files in a snap with the Aruba Solution Exchange. distance for bridging Wireless Access Bulk Provisioning Wireless Access iPad 2 Issues Wireless Access iPhone Roaming issues Wireless Access Aruba 3400 configuration issues Wireless Access Related Discussions Aruba Deployment with Firewalls Colin JosephAruba Customer EngineeringLooking for an Answer? http://scriptkeeper.net/cannot-ping/hp-ilo-ping.html Webinars available 24/7 for viewing at your convenience.

Reference designs, release notes, user manuals, installation guides and more. When digging into the CLI, I did a sho IP int and saw that the netmask of the loopback address was 255.255.255.255 (can't specify in the GUI, just is) , where Me too Alert a Moderator Message 1 of 8 (3,344 Views) Reply 0 Kudos payal Aruba Employee Posts: 18 Registered: ‎03-22-2011 Re: Master-Local IPSec connection not happening Options Mark as New