Home > Cannot Perform > Cannot Perform Requested Operation In Current Session State

Cannot Perform Requested Operation In Current Session State

if you found this guide helpful, please feel free to leave me a comment! For detailed information about Oracle ILOM 3.1.x, refer to the Oracle ILOM 3.1 documentation library at: http://www.oracle.com/pls/topic/lookup?ctx=ilom31 Server modules that have Oracle ILOM 3.0 installed, are supported in a chassis that CMM Software 3.3.8 Notes CMM software 3.3.8 (Oracle ILOM 3.0.12.11.g) provides a fix for bug 18287369 (Java 7u51 requirements for RIAs) for the A90-A/B chassis. The CMM OK LED which is located on the CMM front panel lights up for approximately one minute before turning off whenever the CMM is inserted into chassis or chassis AC weblink

RequestAborted The request was aborted during run time. Project contains too many procedure, variable, and constant names Project file is read-only Project is unviewable. Invalid system-wide (SPI_*) parameter. ... You signed out in another tab or window. http://forum.rebex.net/2396/sshexception-perform-requested-operation-currect-session

Example: Write values from an array to a range object The following example shows you how to write values from an array to a range object. Closing all tabs did the job. The stub received bad data. ... Change the threading model for 'item' or contact the component vendor for an updated version. 'Item' property can't be read at run time (Error 393) 'Item' property can't be set at

FRU ID Data Correction for Oracle ILOM 2.0.3.1 (6631275) Software 1.1 for the Sun Blade 6000 modular system contains a build of Oracle ILOM 2.0.3.1 with a serious bug. This is a bug in Rebex and they fixed it. This will only happen if the stop /CH command is successful. The specified account name is already a member of the local group. ...

An object that describes the selection, expansion, top, and skip options. Block If without End If Breakpoint not allowed on this line ByRef argument type mismatch Calling convention not supported by Visual Basic Cannot define a KWID_tkPUBLIC user-defined type within a private Use your global user account ... https://msdn.microsoft.com/en-us/library/office/gg264318.aspx The address for the thread ID is not correct. ...

PSU Fan Speed Should Run Slower (6853866) This issue was fixed in Oracle ILOM 3.0.6.11. After starting, the service hung in a start-pending state. ... The format of the specified service name is invalid. ... Access is denied. ...

Issues Fixed in SW 3.3 The following issue is fixed in software release 3.3. Line 'item1': Could not create reference: 'item2' Line 'item1': Did not find an index property, and control 'item2' already exists. Doing so will prevent any of the lost data from being recovered. Check out the blog archive.

You should wait for this boot process to complete, then reexamine the LEDs. have a peek at these guys This applies to the following NEM types: 7100090 - Sun Blade 6000 Virtualized 40 GbE Network Express Module X4338A - Sun Blade 6000 Virtualized Multi-Fabric 10GE Network Express Module M2 X4238A A write fault occurred on the network. ... When trying to reset the Sun Blade 6000 Virtualized Multi-Fabric 10GbE NEM SP from the CMM, the reset does not work.

The database specified does not exist. ... However, the large size involved might result in an API error condition because of the large resource utilization. The binding does not contain any authentication information. ... check over here The CMM requires that the NEM light the OK status LED in order to be viewed as powered up and operational.

The format of the specified computer name is invalid. ... When you press the NEM Locate LED in the same chassis, you can use the NEM LED to help locate the CMM from the back of the chassis. In my case, while this was a VM, it was still a production system so outside of a critical outage, I would have had to wait until our next maintenance window

Refer to the Read Me file included with the download for more information about which issues are fixed.

A security descriptor is not in the right format (absolute or self-relative). ... Such description can include more detailed information than WinSCP can possibly deduce from the numerical code. Top Of Page Show: Inherited Protected Print Export (0) Print Export (0) Share IN THIS ARTICLE Is this page helpful? Workaround Insert a valid user name in user property field.

The remote adapter is not compatible. ... a request sent by WinSCP to the server). CMM Software 3.3.2 Notes CMM software 3.3.2 (Oracle ILOM 3.0.12.11.a) is now available. this content DosMuxSemWait did not execute; too many semaphores are already set. ...

Attempt to use a file handle to an open disk partition for an operation other than raw disk I/O. ... If Oracle ILOM displays the fault.chassis.sas.comm.fail fault, this indicates a SAS communication error fault between the CMM and storage blades or NEMs. ItemAlreadyExists The resource being created already exists. A well-known encryption key was returned. ...

Media in drive may have changed. ...