Home > Cannot Load > Cannot Load Exchanger Medium Invalid Element Address

Cannot Load Exchanger Medium Invalid Element Address

[email protected]:1.2.0 FILEMARK....... 1 BLOCKSIZE...... 65536 Press to start reading ... Select Storage Resources | Libraries | | Media by Groups | Default Scratch. If the validation does not succeed for the 32 KB block size, repeat the validation procedure with each of the supported block sizes until the validation succeeds. In the end it turned out to be that one of the tapes had separated itself from the little metal bar that is at the start of the tape, and is Source

X3 © 2001-2013 Comsenz Inc. ض 21. L - PRINTER DEVICE | | . The additional sense code and additional sense code qualifier are contained in that buffer. Click Close.

If you cannot load the media into the drive through the front panel or by using the management software, the hardware is faulty. Occasional Advisor Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎07-04-2006 05:21 PM ‎07-04-2006 05:21 PM Re: NDMP Netapp Backup Check that each tape drive has a valid driver installed. Last thread said 5.5.

If the hardware is faulty, contact your library hardware vendor. You must run the TapeToolGui.exe on the MediaAgent server that is attached to the tape drive the uses the media that you want to test. Right-click the selected media, and then click All Tasks | Delete. The media might have been used by another product previously.

MM0006: Tape block size is not recognized while media label is read While the media is accessed, one of the following error occurs: Error Code 62:1154: While trying to read the P - PROCESSOR DEVICE | | . .W - WRITE ONCE READ MULTIPLE DEVICE | | . . Error code 63:180: Please check if the media has a valid barcode. https://community.hpe.com/t5/Data-Protector-Practitioners/Failing-jobs/td-p/4256632 TapeToolGui reads the media and logs the current file mark and the amount of data that is read for reference.

For more information, see Mark a Media Full.Although the media has bad sections, there might still be valid data on it, depending on where the error was encountered. In addition, you might get error code 40:64. The Code 39 standard supports: the uppercase letters A through Z (no lowercase letters) the numbers 0 through 9 the seven special characters ( - . $ / + % * Honour has been the reward for what he gave (clavin coolidge) 0 Kudos Scott McIntosh_2 Honored Contributor [Founder] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email

From the CommCell Console, select Storage Resources | Libraries. https://community.hpe.com/t5/Data-Protector-Practitioners/NDMP-Netapp-Backup-problem/td-p/3816671 Make sure that the version of the Simpana software is version 10 SP3B or later. The next time you run a qmedia export operation, the command line returns to the prompt after you run the qcommand. MM0005: There is no media in the drive Symptom One or more jobs may be pending or waiting with the error: Failed to mount media with barcode [...] side [...] into

Please format the tape using TapeTest.exe application and try again. this contact form MLMLibInfo::autoDiscoverMedia() - :MLMLibInfo.cpp:6249: Failed to do auto discovery of New Media on Library 25 due to error 289, string Cause The barcode label contains characters that are no longer supported by For more information, see Prevent Jobs from Being Copied. MM0009: I/O errors occur with HP drives I/O errors occur on HP drives on servers that have the follow operating systems installed: Windows Server 2003 Windows Server 2003 R2 Windows Server

Please check whether the SCSI Bus is terminated properly.] For more help, please call your vendor's support hotline. Click OK. To determine which job to disable, examine the error in the Event Viewer. http://scriptkeeper.net/cannot-load/cannot-load-exchanger-medium-incompatible-medium-installed.html Select 32 from the Volume Block Size (KB) list, and then click OK.

If the error occurred during a restore, data that was written to the damaged part of the media probably cannot be recovered. By using this site, you accept the Terms of Use and Rules of Participation. End of content United StatesHewlett Packard Enterprise International CorporateCorporateAccessibilityCareersContact UsCorporate ResponsibilityEventsHewlett Packard LabsInvestor RelationsLeadershipNewsroomSitemapPartnersPartnersFind a PartnerPartner Is the Lib running with full functionaly?And one more: need to check for SCSI cable.

For example: scanscsitool > c:\scsi.txt.

From the CommCell Console, navigate to Storage Resources | Libraries | | Media by Location | Media in Library. R - READ ONLY (CD-ROM) DEVICE | | . . The following appears in the MediaManager.log file: addMedia() - Barcode [OV2100_S20A] contains Invalid Characters. Read, highlight, and take notes, across web, tablet, and phone.Go to Google Play Now »BackpackerMar 2000206 pagesVol. 28, No. 184ISSN 0277-867XPublished by Active Interest Media, Inc.Backpacker brings the outdoors straight to

And then go change your busy drive handling in your library setup in OB.And get patched. If there is no tape loaded, return to the Device Manager and make sure that each tape drive has a driver installed. S - SCANNER DEVICE | | . . .O - OPTICAL MEMORY DEVICE | | . . . http://scriptkeeper.net/cannot-load/cannot-load-exchanger-medium-medium-error.html Cause The export media operation is deemed complete when the media is removed from the IE port.

Right-click the library that is offline, and then click Properties. Honour has been the reward for what he gave (clavin coolidge) 0 Kudos Yogeeraj_1 Honored Contributor [Founder] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to