Home > Cannot Load > Cannot Load Command System Halted Dos

Cannot Load Command System Halted Dos

What do you mean exactly when you say are you booting into DOS or are you going to the DOS prompt in Windows? Cannot load COMMAND.COM. Do you have your bios set to boot to A first. Go to top of page Source

Register User Forum List Calendar FAQ We cannot proceed. Restarted in MS-DOS Mode and from the C: prompt typed my command format C: and it worked perfectly until I got to the part where it said it was ready to When you reboot try FDISK /MBR and then reboot again and format the drive again, reboot and try to load Windows again. Tell me if you still want me to do this?

My Bios will support one drive because it came that way. I can get to the A:prompt - no problem - but if I type in format C: it says I executed a bad command. First of all if you are NOT familiar with DOS, I suggest that you log onto the DOS TUTOR pages.

How to fix it The way to avoid it is to use the COMMAND /MSG switch which loads all error messages into memory, rather than keeping them on disk. Did you have your windows boot disk in the drive when you did this? Find The PC Guide helpful? A caveat: if you've got a $p$g prompt and you've tried to log onto a floppy drive by accident, you'll get Abort, Retry, Fail.

It's a list of every sector on that disk including details on which sectors belong to which file. Visa/MC/Paypal accepted. How to fix it The solution to the first problem is to go back, delete the damaged file and copy a fresh version over from the master disks. Always have a bootable floppy disk handy so if this problem crops up you can boot from the floppy and copy COMMAND.COM over to the hard disk, or use EDIT to

Sorry!!! vBulletin v3.8.1, Copyright ©2000-2016, Jelsoft Enterprises Ltd. When the program completes the system will try to go back to the floppy disk to find COMMAND.COM, see an empty drive, and hang up.

Recommendation: Make sure that COMMAND.COM is Thanks for your patience.

Finding drivers, especially older drivers is a challenge alot of the time. https://www.symantec.com/connect/forums/pxe-boot-error-memory-allocation-system-halted There was a problem looking up the post in our database. The second error message happens when you execute an EXE file and it loads into the first 64Kb of memory (this can only happen with versions 6 and 6.2 of MS-DOS, A disk error was detected while writing a new boot record to your first hard disk.

It uses memory that might be needed by DOS programs. this contact form Got some new ram and tried it in both slots...no go6. Sunny05-11-2003, 07:24 PMHere are a few more links. It's a key component of DOS and it's vital.

Non-System disk or disk error This is an easy one and means you're trying to boot your PC from a disk that hasn't got the operating system installed on it. Then proceed from there with fdisk and then format, just to recover the Drive. If you typed J: and your last drive was C: you'd get the invalid drive specification. have a peek here If the file has a Read Only attribute, the copy won't work and you'll see this error message, How to fix it You can use the ATTRIB command to show file

If you boot from a floppy you might instead see a CANNOT FIND COMMAND.COM error message. Then I fixed all that and installed win98 on the drive, but when I put the drive back in my laptop it just hangs on the win98 screen with the blue Disable unnecessary memory-resident programs and try again.Memory allocation errorCannot load COMMAND, system halted"These are some trouble shooting things I have tried already:1.

DOS ErrorMessages Bad Command or filename. / File (or path ) not found.

It can also be caused in some cases by booting from a floppy disk and then removing the disk from the system after running a program. If you delete it then DOS won't be able to boot, let alone run. When you say "I couldn't execute an fdisk command or any command from where I was so I took out Win 98 startup disk and the Win 98se Cd and tried When I say the dos prompt in Windows I mean the dos prompt in your programs list.

Then I ran scandisk from the hard drive and got the same errors that I got from win98se setup.4. Is this something that I can fix with your help so that I can continue to reinstall Win 98 and then reinstall my software or am I in deep do-do??? It may also be a good idea even if you are familiar with DOS as you may still learn something!! Check This Out Thou if you can play other games or operate your OS without errs then they should be fine.If they show up fine you may clear the Page File if your using

How to fix it If CONFIG.SYS has a SHELL statement and it has been deleted, DOS won't be able to find COMMAND.COM. or /HELP, after the program's name. If you are going to the dos prompt this would explain your problems. It could spell trouble with your hard disk.

Please login or register.Did you miss your activation email? 1 Hour 1 Day 1 Week 1 Month Forever Login with username, password and session length News: Current release: Open Beta When I typed fdisk from the A:prompt it took me into the screen giving me choices about partitioning my hard drive - I did have my boot disk in A: drive Read the links I posted. Edit the PATH command in your AUTOEXEC.BAT file, if you are trying to run a command in another directory that should be accessible from anywhere.

Use DIR /O:D /P to sort your DOS files into date and time order. Thanks in advance for any help that you can give me Bruce. If you try a corrupt or damaged EXE file you'll see the first error message. Copied win98 folder from cd to hard drive in dos and tried to install it from the hard drive....it would lock as soon as I hit enter for c:\win98>setup3.

Sometimes it is difficult to find the correct drivers for your hardware. The Hard Drive was Contaminated, even the Boot Sector. I get alot of old computers in at work that have to be reformatted, that is the easy part. And then format the drive and try to reload Windows.

Press ENTER to quit setup.